AC PORTABLE CHARGER · MODE 2 · UP TO 22 kW
22 kW charging, wherever there is a CEE socket.
The Predixon AC Portable Charger is a Mode 2 in-cable control and protection device (IC-CPD) that turns any 32 A CEE industrial socket into a three-phase charging point of up to 22 kW. No wall box, no installation, no electrician visit — plug it into the socket, plug it into the car, and charge. A CEE-to-Schuko adapter is included for standard household sockets.
22 kW
Maximum three-phase AC power at 32 A
16 A / 32 A
Current selectable on the unit — 11 kW or 22 kW
IP66 · IK10
Dust-tight, water-jet protected, impact-resistant enclosure
5 m
Type 2 cable to the vehicle, 85 cm supply lead
Fixed-charger performance, in a bag
Most portable chargers stop at a household socket and 2–3 kW. This unit is built around the 32 A five-pin CEE plug found in garages, workshops, farms, campsites and industrial sites — so it delivers the same 22 kW as a wall-mounted AC charger, and packs away when you move on.
- No installation. Plug-and-charge on any correctly installed 32 A CEE socket; nothing is mounted or wired.
- Two power levels. Hold the select button for 3 seconds to switch between 16 A (11 kW) and 32 A (22 kW) — choose the lower level when the socket’s fuse is smaller or the circuit is shared.
- Built-in protection. 30 mA AC + 6 mA DC residual-current protection, supply-plug and internal temperature monitoring, automatic pause and automatic restart after a fault clears.
- Rugged by design. PC + ABS housing rated IP66 / IK10, flexible cable that can still be coiled easily in the cold, and cable guides and a clip for tidy storage.
Power levels
Actual charging power depends on the socket, the electrical installation and the vehicle’s on-board charger:
| Supply | 16 A | 32 A |
|---|---|---|
| Three-phase (CEE 32 A, 400 V) | 11 kW | 22 kW |
| Single-phase (230 V) | 3.7 kW | 7.4 kW |
| Household socket via Schuko adapter | 3.7 kW (16 A) | — |
Single-phase and three-phase operation depend on the model variant and the supply. The Schuko adapter must only be used on sockets with a suitable fuse and installation.
Status at a glance
| Indicator | Meaning |
|---|---|
| No light | Power off |
| White LED bar | Powered on, ready |
| Green LED bar | Charging (running light speed shows the selected level) |
| Red LED bar | Fault — see the troubleshooting guide in the user manual |
| 11 kW-16 A / 22 kW-32 A | Selected current level |
Where it fits
- Homes and holiday houses with a CEE socket but no wall box
- Workshops, dealerships and service centres charging customer vehicles
- Fleet depots, farms and construction sites with industrial power
- Campsites, events and temporary locations
- A back-up charger kept in the trunk
Technical specifications
| Specification | Value |
|---|---|
| Electrical | |
| Maximum power | 22 kW |
| Voltage / frequency | 3 × 230/400 V AC, 3P + N + PE, 50/60 Hz |
| Current | 6 A – 32 A (16 A / 32 A selectable) |
| Charging mode | Mode 2 (IC-CPD) |
| Residual-current protection | 30 mA AC + 6 mA DC |
| Temperature protection | Supply-plug and internal temperature monitoring |
| Fault behaviour | Automatic charge pause and automatic restart |
| Cable & connection | |
| Vehicle connector | Type 2 (IEC 62196-2) |
| Type 2 cable length | 5 m |
| Cable type | H07BZ5-F 5 × 6 mm² + 1 × 0.5 mm² (EN 50620) |
| Supply plug | CEE industrial plug, 32 A, 5-pin (3P + N + PE) |
| Supply lead length | 85 cm |
| Adapter | CEE to Schuko, 16 A (single-phase) |
| Interface | |
| Current selection | 16 A (11 kW) / 32 A (22 kW), button on the panel |
| Indicators | POWER, CHARGING, CHARGER STATUS LEDs |
| Enclosure | |
| Material | PC + ABS |
| Ingress / impact protection | IP66 / IK10 |
| Dimensions (H × W × D) | 280 × 110 × 63 mm (control unit) |
| Weight | 4.6 kg |
| Environment | |
| Operating temperature | -30 °C to +75 °C |
| Storage temperature | -50 °C to +85 °C |
| Compliance | |
| Standards | CE, IEC 61851-1, IEC 62752, IEC 62196-2, IEC 61851-21-2 |
| Directives | 2014/35/EU (LVD), 2014/30/EU (EMC) |
| Recycling | Electronic waste (WEEE) |
Values may vary by model variant; the rating label on the unit is the reference for the exact configuration.
In the box
- Charging unit with 5 m Type 2 cable and CEE 32 A plug
- CEE-to-Schuko adapter (16 A)
- Connector protection cap
- User manual
Safe use
- Portable Mode 2 equipment — not designed for fixed installation.
- Use only on sockets with a correctly rated fuse and installation; do not use extension cords or additional adapters.
- Do not drive over the cable; keep the connector and control unit away from water jets.
- Stop charging from the vehicle before unplugging the connector.
Talk to us
Fleet, dealership or distribution enquiries — tell us how many units you need and where they will be used, and we will come back with pricing and lead times.